Chinese | English
Large pipe bender equipment
Mechanical parameters
Processing range |
1”—8” |
3”—16” |
8”—24” |
16”—30” |
20”—36” |
24”—40” |
30”—48” |
32”—56” |
36”--64” |
Pipe thickness |
Sch40 |
||||||||
Max.pressure |
31.5MPa |
Chain-Drive Pipe Bending Machine |
|||||||
Working pressure |
25 MPa |
||||||||
Working speed |
0—1000mm/min |
0—1500mm/min |
|||||||
Return speed |
1500—2000mm/min |
2000—3000mm/min |
|||||||
Cylinder Diameter |
125mm*2 |
140mm*2 |
180mm*2 |
200mm*2 |
250mm*2 |
Compared with hydraulic pipe bender.the chain-drive pipe bending machine has the following
features: |
|||
Cylinder stroke |
3000mm |
4000mm |
5000mm |
8000mm |
8000mm |
||||
Cylinder thrust |
30T*2 |
38T*2 |
63T*2 |
78T*2 |
120T*2 |
||||
Motor power |
13kw |
18.5kw |
24kw |
28kw |
32kw |
||||
Transformer required for quenching |
500kwa |
1000kwa |
1000kwa |
1500kwa |
2000kwa |
2500kwa |
3000kwa |
3500kwa |
4000kwa |
IF power supply required |
160kwa |
250kwa |
300kwa |
500kwa |
600kwa |
600kw |
800kwa |
800kwa |
1000kwa |
Mechanical video
Equipment details
Large pipe bender equipment
In the field of mechanical hydraulic pipe fittings, pipe bending machine using in the market accounted for the proportion of larger, in life, in the construction of public infrastructure have greater importance, I company produces good bending, but also produced good pipe bender, like intermediate frequency pipe bender is the technology of PLC system, so as to better meet the needs of the customers.Large pipe bender equipment mainly includes: frame, main cylinder support plate (including main cylinder), movable push plate, elbow clamp wheel platform, elbow rocker arm, rocker arm rotating shaft, elbow combination chuck, intermediate frequency transformer bracket, intermediate frequency power supply, intermediate frequency transformer, electrical control system and so on.
Pipe bending machine: the use of the working cylinder screwing gear block of internal thread, depending on the bent pipe diameter selection mode, the fortress, set the column will be two roll groove which corresponds to the die, and then into the corresponding size of the plate hole, insert the curved pipe groove, then the quick joint activities section of the high pressure oil pipe end back, and set on the joint of oil cylinder and oil pump, the pump on the oil drain screw tightening, can bend, bend over, relax the oil drain screw, piston will be automatically reset.The benders produced by the large pipe bender have beautiful appearance, high quality and high production efficiency.
Large caliber medium frequency pipe bender
Large caliber medium frequency pipe bender mainly produces pipe bender.The bed body is made of welded plates and profiles, which are supported on the tailstock and hydraulic tank.The bed body is equipped with guide rail, elbow head, mandrel mechanism, etc.There is a trolley on the guide rail and a travel switch on the bed body.The second is the elbow head and the third is the car.These three constitute the important parts of the elbow pushing machine.The steps of the use of the push machine The steps of the bending pipe are roughly as follows:
1. Set aside the straight length of the first section and clamp the tube 2. Bend.3. Loosen the mold, take out the tube, and reset the mold.Check the shape of the tube on the inspection fixture according to the standard sample of the tube and correct it.4. Place the tube in the mold according to the desired shape and clamp it tightly.5. Bending.6. Repeat step 3 until you have finished bending the pipe.
Regardless of elbow push machine or elbow push machine, it is an important project of transportation and exploitation after oil and gas exploitation.In the national heavy industry, construction and each hydraulic market have a large proportion, so our company for the push machine technology development journey has never been interrupted, medium frequency heating induction technology PLC system, cold push system, hot push system, stamping method are optional push process
402-403.